Q&A for Nutone Central Vacuum Units
All Products for Nutone
Nutone CV653 Runs For 10-15 Minutes
Question:
My Nutone CV653 is about 15 years old. It runs for 15 min then stops. We wait 15 min. reset the breaker on the Nutone and it runs for 10 more min. If it is the motors, would you suggest purchasing a new unit (which one) or replacing the motors. Thanks, Richard, Chestertown
Answer:
This generally indicates that your motors are failing and needs to be replaced with Lamb Motor 117507.  This is the most cost effective solution over replacing the entire unit. 

Nutone CV350 Tripping My Power Strip
Question:
I have a 10 year old NuTone CV-350. After running for 15 - 20 minutes, the power strip breaker into which it is plugged trips off. Is this caused by overheating of the motor? Could it be the power strip is not of the correct size? Or anything else? Oakton Virginia
Answer:
The breaker(s) on a power strip are not as robust as your typical house breaker and will fail over time.  Your best bet is either to 1) replace your power strip with a 20 amp strip or 2) connect your central vacuum system directly to a house outlet on a dedicated 20amp breaker.

CC315-B Power Head Hose
Question:
I need the model # for a replacement hose to fit a Brian powerhead model #cc315-b. Charles. Gallatin
Answer:
The replacement hose should be the electric hose on this page http://builtinvacuum.com/help/nutone/hoses.html. Let us know if you have any further questions.

CV-450 Always On - Bad Relay or Reset.
Question:
I have a Nutone CV-450 w, Installed May 2001. Mine also will not shut off unless I unplug it. All that I have read is it is the relay switch. Which one is the relay switch? Also my reset button (model #MB1) is broken, could that be the problem? Jim in Las Vegas, Nv
Answer:
How do you know the reset is broken? If it is sticking out over an inch and will not go back in then it is broken. Plus, if it was broken then the vacuum would not operate at all, there would be no electricity flowing. Let's say the reset is good for now. The issue, then, is your relay which is probably on a circuit board. Please contact nutone for this board www.nutone.com. We havea  generic replacement (www.builtinvacuum.com/retail/shopretail.php?part_no=235M) but the original may fit better.

Nutone 556 Replaced with SilentMaster
Question:
Nutone CV556 Do you have replacement filters for the Nutone CV556? Can the system be converted to use bags? Worst case, how hard is it to change out the whole unit for a SilentMaster? Would I be able to keep the existing plumbing/hoses and just replace the main central unit? Thanks, M.T. UT
Answer:
Unfortunately, we do not carry replacement filters for the Nutone CV556. As we do not have detailed information regarding this particular unit.  You may replace your system with our Silent Master system.   Note, you are not required to change any of the existing plumbing or hoses you currently have.  We recommend that you contact one of our dealers located in your area to give you pricing and additional information on replacing your unit with a SilentMaster.  Please use the following link to locate a dealer near you: Locate Dealer.

Nutone 698 Power Head
Question:
NuTone model #698 type C Power Head, just started making a real bad grinding noise, sounds like it's breaking up inside. Is there bearings in that thing that may be falling out of place? Or busting apart? It's about 15 years old, but by no means, is it overworked. Where can I purchase a new power head? Thank you..Patty in Winnipeg Canada
Answer:
We are confident the replacement power head is one often used by and sold under many different brands here http://builtinvacuum.com/retail/shopretail.php?part_no=482N

Testing Power on Unit, Inlet, Hose
Question:
I have a brand new Model VX3000C. There is a manual on/off switch on the front of the unit, which works fine. I turn the manual switch off and the green light stays on. I assume the manual switch should be "off" for normal operation. Outlet terminals and wiring have been triple checked but the vacuum will not run using an outlet and the hose unit. I turned the unit on manually and removed the low voltage wire and it continues to run. I'm not sure how to get this vacuum to run with the hose.
Answer:
The vacuum is to stay in the off position. When the low voltage line is crossed the suction turns on. Try shorting the low volt connection on the unit. It should turn the vacuum on. Try shorting it at a wall inlet valve (touch foil on the two contacts INSIDE the suction hole). If that works then it may be your hose or the low voltage wire used was not 20 gauge but thin like telephone wire. Let us know and we can help.

350W Will Not Stop Running
Question:
I have a NuTone 350W and when plugged into power it will not stop running. I viewed the answer you had for the 450. Is the procedure the same for the 350W? Also, I am not sure how to locate the Low Voltage Wire. Do you have instructions for that? Thank you.
Answer:
Yes, same procedure. The low voltage wire is the wire following the intake pipes from the home and connects to the outside of the tank. Remove one of the low volt wires to do the test. Plug the unit back in and if it still runs then the relay/board is bad. If it doesn't run then there is a short in the home. Use the guide here for more troublshooting and to look for places it may short. www.builtinvacuum.com/flowchrt.html

CV315-B Power Head Replacement
Question:
I have a broan mod. cv 315-b powerhead its about 14 years old and wore outscrew holes brokenfor the mtr hold down can I get a newer style that will fit my older hose and power cord? thanks Kal.
Answer:
There aren't many replacements available like that these days. The connections are different now as well as the wand. But there are still a couple that will fit http://builtinvacuum.com/retail/shopretail.php?part_no=466,482,482I

CV450 Drawing 15 Amps or More
Question:
Have a cv-450w that is drawing about 25% more current than label says putting it slightly over15 amps it is on a 15 amp circuit so it eventually trips. What is total amperage supposed to be for this unit? Maybe it should be on a 20 amp circuit or is it that the motors should be replaced
Answer:
The CV450 has two motors in series, meaning the top motor is pulling the exhaust from the second motor much like a turbo in a car. Therefore the amps are always peaking but it should be below 15. As the motors get older they can draw more before they stop working. If the unit has worked well on the 15 amp house circuit then it's most likely the motors going bad and demanding more amps. If that sounds like the case then change the motors before you change the circuit. You can find the motors here http://builtinvacuum.com/help/nutone/motor.html

Dual Motor Replacement and GFI Circuit
Question:
I have an 11 year old Nutone CV-450 that has started to run very hot after 5-10 minutes and often trips the 110V GFI receptacle. It does run cooler, however, when on board vacuum port is slightly opened- a temp work around. All 5 wall receptacles have equal and fairly good vacuum ruling out blockage. That said, I'm assuming the unit has two motors one of the two is failing and I should replace both since I have no way to pinpoint the culprit. Your "single" motor replace guide seems straight forward. Is there a reference for replacing two motors which I conclude are top: 116210-85 and bottom: 119412? Thank, Pete, Moultonborough, NH
Answer:
A central vacuum should not be plugged into a GFI circuit. It causes more trouble and false alarms then good. With the minibreakers on the vacuum tank and the house panel breaker as a back up there is enough protection. For dual motor replacement it is really as straight forward as the single motor replacement so you can use those instructions. We do recommend both motors being replaced because the other "working" motor is always not far behind to fail and you'll be back in there again.

Circuit Breaker Pops When Hose is Disconnected
Question:
Nutone CV-353 Question: I have recently replace both motors in this unit (CV-353) originally purchased in 1997. The unit was running fine after the replacements, but is now throwing circuit breaker after use. Reset circuit breaker, use vacuum without issue, but circuit breaker throws when hose is removed from wall inlet. Circuit breaker seems a little soft, does it need to be replaced or is there a short somewhere in the system? Thanks, David Taylor Johnsonville, SC.
Answer:
Most likely the motors or one of them is bad and heating the minibreaker. The minibreaker can go bad as well though. You can replace it for less money than a motor to see if the issue is solved. If not then replace the motor that smells more like it overheated. The hose being removed will have nothing to do with this issue.

Replace CV-750
Question:
I have nutone CV-750 about 10 years old. In the middle of usage it lost about a third of the suction. Would you recommend replacing a specific part (if so, what part)? Or would it be more cost effective to replace the entire unit? If so what unit would be a good replacement? Norma, Elkton, MD.
Answer:
The CV-750 has two motors connected to each other like a turbo. It's not ideal and not many vacuums are created like this any more because the motors run hot. Motors have come a long way since and offer as much cleaning power. We suggest replacing the CV750 Nutone Vacuum with a SilentMaser S44. They are available through local resellers available in our dealer locator on the website.

What Hose for What Model?
Question:
Hello, I have Nu tone CV-450 unit and need to replace the hose. Unfortunately, I do not have the original hose at home, therefore I can not check what model it was. Please, can you let me know, what hose model I can use with this unit? Thank you, Jurgita
Answer:
There are several hoses used with that unit and any unit. It solely depends on the vacuum tool used if you have any carpet. If the vacuum tool has an electrical cord then you need the electric hose. If it doesn't or if you have no carpet then you need the low voltage hose.

Electric Hose for CV850
Question:
We have a nutone cv850 installed and need to replace the hose. Will the 35ft Direct Connect 353G fit both the outlets and the accessories? Thanks, Jess (Florida)
Answer:
Yes, the #353G will fit electric wall inlets with two holes 3/8" apart from each other. The handle end will fit most all accessories sold with Nutone systems. If there is a 2-inch space between the metal nipple on the handle tube and the start of the two holes for the electrical then you are good to go. Or if the power cord from the head is manually plugged into the handle's electrical two holes then you are good to go as well.

Wiring Low Voltage to Nutone 350
Question:
have a very old nutone 350 wires broken from where it says 16 volts class 2 circuit can u please tell me where to connect those thin wires thanks
Answer:
Wires that go to the vacuum tank attach to two terminals. It doesn't matter what terminal each wire goes to.

CV16 Lost Power
Question:
I have a 20+ yr old Broan CV-16 with a cloth bag. I've suddenly lost suction power at the unit and the outlets throughout the house. I tested the inlet @ the unit w/out the hose. What could be causing this?
Answer:
Usually that is a dead motor. Please use the troubleshooting chart to find the issue and solution http://builtinvacuum.com/flowchrt.html

Replace Nutone 353 with More Power Unit
Question:
I want to replace my nutone 353. I have house with 2500 sqft. What would be recommendation for unit to be replace with. I have mostly every where hardwood floor accept family room.
Answer:
We recommend our SilentMaster S44 or Flo-Master M85 here http://builtinvacuum.com/products.html. They are available from a local dealer and will give you 50% more power and be quieter. These new units empty from the top and are compatible with your system.

Main Panel Tripping Once Per Day
Question:
Hi, my Broan VX6000C is one year old. When I command the `first start of the day`, the circuit breaker will trip on the house main board. After a single reset, the unit will work, stop, start, etc till I am done vaccuming but I will have the same issue the next day. It has it's own electrical circuit. I already completely changed the house electrical circuit. The issue stopped for 8 months when I switched it from 15amps CB to 20amps CB but it restarted recently.
Answer:
That is a unique issue and one we will have to recommend an electrician to look at. Thank you for asking.

Low Voltage Wire Connections
Question:
I am replacing the piping and some wiring on my Nutone central Vac system . Some of the iutlets had two 18/2 wires going to them and some have one 18/2 wire. Are the wires all in series or does it matter how they are connected to he outlets and spliced together in the crawl space? Steve, Manasquan, New Jersey
Answer:
It really doesn't matter how or where they are joined, looped, daisy chained, or grouped together. Just keep one wire from touching pair and you'll be perfectly fine.

Unplug Unit to Stop Suction
Question:
we have a Nutone central vacuum model 350, about 35 years old. It does not shut off when the hose is removed and has to be unplugged to get it to shut off. Can you give me some reason this is happening and a solution? Susan
Answer:
It sounds like the relay has gone bad. Double check using the troubleshooting and solutions guide here www.builtinvacuum.com/flowchrt.html

Transformer Replacement?
Question:
I have a 350 Nutone Vacuum System. I need Transformer Assembly Part No. 64672 (539B) and Relay 63206 (5173). Can you help. We just replace the Vacuum Reset Button and you still have to bang on the Relay to get it started. Can you help.
Answer:
These parts are no longer sold and the comprehensive electronics replacement is the single power board. It is retroffited in. It actually saves money and makes the electronics easier. Here is the one for all single motor vacuums. Use the large photo as the wiring guide. http://builtinvacuum.com/retail/shopretail.php?part_no=235S

Turns Off But Runs Later
Question:
I've got a VX6000C that runs for about 15 minutes and then stops. I wait awhile and it will run again for 5 minutes before stopping and so on. I can't find any blockages. My kids have a bad habit of standing on the hose while I vacuum, could damage to the hose cause this kind of reaction from the unit? Thanks a ton. Cam
Answer:
No real damage, it is a natural thing that happens as the motor dies. They don't slow down, they do what you are experiencing.

Bad Board - Always Tripping
Question:
I have had the VX475CC power unit for 4 years. It has often tripped the circuit breaker for it's circuit on start-up. Now, the actual vac will stop running after 3-5 minutes, but the circuit/outlet is still energized. What do I need to test or replace?
Answer:
If it has been a constant problem and now getting worse you probably have a bad circuit board from the beginning. Talk to the manufacturer for a warranty replacement board.

New to Central Vacuum - Need Hose and Tools
Question:
We purchased our home complete with a 350 Nutone Central Cleaning System but have not been able to use it as we need a new beater bar and hose. Can you recommend exactly what we need, where we can get these items, any suggestions, and lastly the price please and thank you?
Answer:
Congratulations on your home! Your vacuum works perfectly fine with every hose and tool kit available today. That means you can get the kit that works best for your exact flooring type and budget. If you have carpet buy an electric kit, if no wall-to-wall carpet buy a non-electric kit. We have them listed here with prices http://builtinvacuum.com/help/nutone/kits.html. Most likely, if you want an electric kit, you will choose one with a pigtail corded hose that plugs into the wall vac inlet and a nearby electrical outlet. If you need more help please call us or one of our dealers in your local area.

Nutone Relay 3ARR4BA32
Question:
Hi, Have an old Nutone 350. Need relay (3ARR4BA32), but it is hard to find. Is there any way to fix it? Thanks. George
Answer:
We recommend retrofitting a circuit board into the unit which takes place of all other components except the motor. An electrician can use the photo of the product online as the easy wiring guide. http://builtinvacuum.com/retail/shopretail.php?part_no=235S. Many homeowners opt for this to save money and because they can't find original equipment.

Broan Won't Turn On
Question:
Broan VX3000c doesnt power on Question I tried to turn it on manually from the unit - doesnt turn on. The pail is very clean. Breakers have been verified and also changed inlet. the green light is on so i know there is power. I shut it off for 20 min and still does not turn on. What do you recommend I do next? Mario Carciero from Montreal, Canada
Answer:
You may have a motor or a circuit board failure. Follow our troubleshooting guide to help narrow down the issue at http://builtinvacuum.com/flowchrt.html

Broan V28C Runs But No Suction
Question:
have a Broan built in vacuum model-V28C-3 motor runs but will not suck Julie ,Turtleford
Answer:
There is either a pipe connection that has come apart or there is a clog in the system. You can contact a local dealer to inspect and repair at http://builtinvacuum.com/dealers.html

Replacement Belt
Question:
I need a belt for my central vac brusher unit. It is a household type :828, Model:398 NA, serial number:0218625. Thanks, Jerry
Answer:
We don't have a cross reference for that model. You can compare the measurements of the belts we stock to your old one. If the measurements match, it is your replacement belt. http://builtinvacuum.com/parts/belts.html

Broan CV30 Venting
Question:
I have a Broan CV30 unit. Is this unit supposed to be vented to the outside? Currently it has only a short flexible hose coming from outlet. If not vented to outside what are my options?
Answer:
If the unit is not in a small enclosed area like a closet, then you don't need to vent the exhaust.  If you need to vent, add piping to the exhaust port and run it outside.

CV450 Correct Replacement Motors?
Question:
I have a Nutone CV450 central vac unit and both motors have failed. There was a scraping noise shortly before they failed. Before I order replacements I want to confirm they will fit. The numbers I see on the upper motor are 6116-00 and 340389FE. For the lower the numbers are 720588FE and 894. The unit is 22 years old. Will the motors you offer work? Thank you.
Answer:
Yes, the motors in the Nutone motor chart for the CV450 are the correct replacement motors. The other numbers you found on the motor are part numbers for the what makes up the motor and are not completed motor numbers. Here is the Nutone motor page http://builtinvacuum.com/help/nutone/motor.html

Broken Button Lock
Question:
My push button on the power hose that holds the wand from coming off broke.It appears that it is just a flat metal piece with a button connected with an upper rivet. Is this part avaliable? David Jennett
Answer:
You can either replace the whole handle, or add an internal button lock found here, http://builtinvacuum.com/retail/shopretail.php?part_no=300B

Broan VX3000C Shuts Off After A Few Minutes
Question:
john, victoria,bc have a broan vx3000c, which shuts off after 10min, motor looks good, brushes are good---runs fine on bench at 11.5amps unit is 4 years old any ideas?
Answer:
It may be having an overheating problem.  Check that all the filters are clear, even the screen just before the motor on the inside. 

Brush Has No Power
Question:
I recently bought a Nutone CT700 brush and wand, but I cannot get the brush to start spinning. I am getting suction at the hose (I am using an old hose that I am guessing is the problem), but the new unit will not spin. I came across this on ebay... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=150562313672 Do you think this might be the problem?
Answer:
It could be a bad switch or a blown fuse in the hose.  The problem you're having is that no electricity is being sent to brush, and either of those parts can cause the problem.  You may want to have a repair technician take a look at the hose first to locate the problem and save you a lot of time.

Nutone Will Not Turn Back On
Question:
Ww have a NuTone central vaccum that is very old and I used it for the first time today and it worked very well.I had it on for quite awhile and changed bag and 2nd filter.It will not turn now.We do here a clicking sound.Do you think it overheated.Have I blown the motor?
Answer:
The motor may have overheated and shut down. Try it agian a little later. If still no power, then the old motor has finally given up and needs to be replaced.

No Power To Carpet Brush
Question:
We just bought a house that has a CV353W Nutone unit, everything works ok except the power brush, we have power at the inlets. We purchased a new head and it still does not work, what do you think it could be? Thank you Scott Lock Haven, PA.
Answer:
There could be an issue with the hose switch or the fuse. If both are not working properly, the brush will not get any power. Try replacing the fuse first, if that doesn't fix the issue then replace the switch.

Older Unit Parts
Question:
I have a model 350 that needs a replacement debree canister. Is there any place to purchace the part or is it to old? If so will any newer models conect to the current set up in place?
Answer:
Those are not available as far as we know. You can try contacting a Nutone Dealer to see if they have any old inventory or used parts.

Will Not Shut Off
Question:
Model CV-450, will not shut off even after disconntecting the low-volt wires. Where is the reset button? Thanks Bill
Answer:
Please use this guide to determine what is wrong www.builtinvacuum.com/flowchrt.html.

Nutone CV30D Attachments
Question:
Hi, I just moved into a house with a cv30-d and have no idea how to use it. Is there somewhere I can get a users manual? Also I need attachments because previous owner only left a hose. Would appreciate any help you can provide. Cindie
Answer:
We have a large selection of kits available to complete your home vacuum system. Each available kit has an option labeled ""NO HOSE". This will include every part listed except the hose. Call us to speak to a technician prior to ordering to ensure that your current hose will be compatible with standard products.

Nutone CV-450 Burning Smell
Question:
I have a NuTone CV-450 that is approximately 8 years old. It would not turn on so I hit the reset button. It starts and will run approx 2 seconds then cuts off. It has a slight burning smell when it comes on. Is this signs of a bad motor?? If so...should I replace the motor or unit? If I need to replace the unit, what new model would hook up easily without a lot of problems. Thanks. Danny - Woodstock, VA
Answer:
That burning smell is the death of your motors.  They can be replaced, you can find the right motors here, http://builtinvacuum.com/help/nutone/motor.html#motor just go down the list to find your model number.  Should you decide to upgrade to a new unit take a look at the power of these units! http://builtinvacuum.com/modernday/index.html 

Relay for Old Unit
Question:
We have an old Broan central vac unit Model 154 N16 purchased in 1974 manufactured by Beam Industries in Webster city, Iowa. I beleive the relay is bad, the only numbers on it are (GE) 3ARR4BA32. (240 volt/24 volt) I would like to get a replacement relay. Thanks Sam in Middletown
Answer:
We don't have a relay for you, but many are using this circuit board to replace all the electronics for less money. Your electrician can install it in under an hour easily. Use the large photo as a wiring guide http://builtinvacuum.com/retail/shopretail.php?part_no=235S. We have other boards for 240 volt and dual motors here http://builtinvacuum.com/parts/electrical-parts.html

Nutone 599 Vacuum Parts
Question:
Barbara, Saylorsburg. I have a 599 nutone powerhead which needs some new parts. Do you know where I can find these.
Answer:
Hi, we carry the replacement vacuum head and the belt. We do not have other parts for this brush at this time. Thanks for asking and here is what we have http://builtinvacuum.com/retail/shopretail.php?part_no=482N,48201.

Broan V28C Filter
Question:
How do I clean the filter of a Broan V28C central vac? Can this be removed? If so, how do I do that? Thanks.
Answer:
Hello, that is either a center weighted cloth filter or a disposable bag. Remove the lower section of the unit to find out. A cloth filter is cleaned but shaking it into a plastic trash bag. Some remove it and wash it, and some replace it. To remove pull an edge inward until the outer rim flexes and the whole filter falls down. Be sure the filter is 100% dry before replacing. We have 11.5 inch and 14 inch diameter replacements.

New Home, Old Vac
Question:
bought house with CV850 unit, some inlets have no suction, anyway to check if these inlets are connected to the unit? Also is there a place i can get instruction manual? How do I check if I need to empty or change the dirt bag? Trying to open the bottom part after unlatching, assuming is a place where dirt is collected, but is very tight and am afraid to pull it hard as dont know if I will break it. light on the unit is green. please help
Answer:
Congratulations on the home and central vac. The two inlets should be connnected but are clogged. See solution #3 here www.builtinvacuum.com/flowchrt.html for help. We don't have an instruction manual but the only maintenance is changing the bag (#723 bag). You have to knock the lower part off after you unlatch, it will come off. There is more help and supplies found here http://builtinvacuum.com/help/nutone/motor.html

V20C-3 Motor?
Question:
I am looking for a replacement motor for a Broan central Vacuum model V20C-3. Please tell me what replacement motor should I order. Regards, Dawn M
Answer:
Hello Dawn, the correct motor is listed on this page, row 3, where is says CV20 and V20C. http://builtinvacuum.com/help/nutone/motor.html Thank you for asking.

Continuation from Bad Transformer
Question:
Continuation from "Bad Transformer" Verified 120 volts at outlet when unit is operating, line wire gauge is 12, ground is good. To clarify, i replaced the controller board with one from Nutone for ~ $160. The new one measured 5.07 volts on low voltage terminals. Low voltage wireing to outlets is 18ga, checked some connections and they look to be soldered and wire nutted. This seems to me to be a manufacturing issue with these boards, wrong transformer with inadaquate voltage/current to hold the relays closed. Or could this be a switch problem in hose which measures 15.7 ohms.
Answer:
Our experience tells us the issue is the lack of voltage from the transformer. Return the board for a new one or buy one of ours. You'll save $100 or more buying from us.

Bad Transformer?
Question:
Transformer Bad? This is a continuation to the above titled "Transformer Bad?" I could not figure out how to use your transformer on my old control module so i just bought another one. I installed it and the system worked for a few months. The switch voltage measured 5.07 volts, not 24 volts as the sticker, but it did work. Well now it does not work again, with the same symptons that it will sometimes come on and sometimes it won't. I of course checked the hose switch and it measures 15.7 ohms in both positions, steady. The voltage at the outlets is a steady 5.07 volts. Any suggestions?
Answer:
You may have bought the wrong transformer. You may have a low voltage issue in the home if the wire is not at least 20 gauge. The valves that don't work at times, can you short the contacts at the valve and make it start? If so then there is not enough power to power the hose switch. We measure 12 volts coming out of our transformers. You have 5 which is suspect to begin with. The next solution is to maybe have your electrician try a circuit board. They have all the components and retrofit into the machine easily, see them here http://builtinvacuum.com/parts/electrical-parts.html

Nutone 750 Trips Breaker
Question:
my nutone is cv750. It is about 10 yrs old and we never could get it to work right. It runs good for about 7 mins. Then trips the reset. If you reset it it works for about 5 mins then trips again
Answer:
If you could never get it to work right and it always tripped the minibreaker then a motor is bad or the minibreaker, but most likely the motor. When a motor IS bad it trips the minibreaker after a few minutes. Your system has two motors in series. You can get away with replacing the bad motor if the other motor doesn't have lots of usage.

Unit Shuts Off then Starts
Question:
Dale Molalla oregon nutone cv850 runs while and then shuts off and then starts again after a few minutes. I wired a fuse around the relay and it worked a few weeks and then the fuse blew and I replaced the fuse and now it does the same thing again.???
Answer:
Dale, the motors are going bad. It is time to replace them, or maybe the brushes if the motors are not at 900 hours or so. The motor is here http://builtinvacuum.com/help/nutone/motor.html. If the original motor is the same as the replacement then here is the brush http://builtinvacuum.com/retail/shopretail.php?part_no=210X. Each motor takes two.

Lost Some Suction, Two Motor System
Question:
Nutone CV450 approximately 9 years old. Suction dropped about 30% ?overnight?. All piping, bag, and cloth filter are OK. What is the procedure to check and then replace motor brushes? Thanks! Tim Roxbury
Answer:
Tim, one motor is likely fried. Bang the machine and it should work again. Also look for a mini breaker to push in. Changing the brushes may help for awhile but it is better to replace the motor. You can view the motors for the model here http://builtinvacuum.com/help/nutone/motor.html and find the brushes for the motor by searching for them by motor number in our search box. Click on the instructions link for how to get to the motor and click on the instructions link in the motor brush text for those instructions.

Broan Filter 99010172
Question:
Broan CV30D Do you stock the replacement motor filter 99010172 Do you stock the replacement motor filter 18 gasket 991000458
Answer:
Hi, please see the right side of the grid here for the filtration offerings. You will have to take a measurement to be sure we have the correct replacement. The CV40 doesn't have a match from us so please take the measurement. http://builtinvacuum.com/help/nutone/motor.html

Transformer Bad?
Question:
I have a NuTone CV750 approximately 5 years old. Recently started to shut off when in use after a few minutes. Checked brushes, only 1/3 worn (bought new ones based on another sites recommendation). Unit works fine with unit mounted switch. Checked low voltage circuit and it measure 5.02 vdc, sticker says it should be 24 vdc. Noticed that there is line voltage (120 vac) between heat sink and ground (got a shock). Examined the control board which has the transformer on it and there are no obvious damaged parts, burned components or shorted wires. Added a piece of edge aligator strip to heat sink to ensure line wires do not get abraded.
Answer:
Hi, you need the 24 vdc at the low voltage wire connection. If you don't then the transformer is bad most likely. The unit's switch may be bypassing the low voltage so that is why it works, or it may just be that it has enough juice at that proximity. Our #232 transformer may work for you.

3ARR4BA54 Relay Replacement?
Question:
I am told that the relay for a old Nutone model 350 is no longer avaiable. The relay is part # 3ARR4BA54, any ideas where to get one? Fred-West Chester Pa
Answer:
Your electrician can easily replace all the electronics for less money with a single circuit board here http://builtinvacuum.com/retail/shopretail.php?part_no=235S. Print the enlarged photograph for a guide. For two motor systems use board #235M and large two motor units #235L.

Suction Weak at Unit, What Next?
Question:
I have a Nutone 353 that is 25yrs old with no previous problems. However now the suction at all the different room inlets is almost nil, including the inlet at the front of the unit. I have tried all 3 different hoses I have, with no change. The motor seems to be running like it always has -- doesn't sound weaker. Nothing is holding any of the inlets open, and the cork-like gaskets on them are all good. I haven't got into the motor to look yet -- any ideas on what I should be looking for would be greatly appreciated. And if it is motor related, at 25 yrs. is there an advantage to just replacing the motor vs. buying the whole new unit for just alittle more $$$ ? Thanks in advance for any help. Mike L. Spokane, WA.
Answer:
Hi, Disconnect the pipe coming in from the home and duct tape closed that connection on the vacuum unit. Now the vacuum is stand alone. Test suction. Remove the bag and look towards the motor for any secondary filtration and take it out. Put the unit back together with no filters and try the suction at the unit. If still weak then the motor is clogged full of hair and thread and needs replacing or the electricity into the unit has dropped for some reason and the motor is not spinning as fast as it should. Motors don't slow down with age, so there has to be a reason. Most customers replace their motors over buying a new unit. However with new units that fit right in and offer 50% more power and long life, the decision is getting harder. Our FloMaster M85 is right around $500 and makes a wonderful replacement. Check it out here http://builtinvacuum.com/flomaster/

Reset Buttons Always Popping
Question:
My nutone cv 350's reset button keeps on popping after 2 seconds. Bag is fine and I unhooked the unit from the incoming hose. Any suggestions? Gino
Answer:
Hi Gino, the motors are overheating, meaning they are basically ready to be replaced. We have the replacements here and they are easy to swap out. http://builtinvacuum.com/help/nutone/motor.html

Low Suction at Some Inlets
Question:
My nutone vaccuum outlet in my kitchen and one upstairs on my second floor does not have good suction. The other outlets in my house are fine and have a strong suction. What can be the issue? Thanks, Lisa :)
Answer:
Hi Lisa, you have a clog and you can probably get it out yourself using a simple technique. Plug the hose in and turn the suction on. Let the suction build up by putting your hand over the hose end. Let go. Do this for 5 minutes at both inlets. If it doesn't work then suck in a paper towel at one inlet and do the suction thing again. If that doesn't work use the solutions under number three here www.builtinvacuum.com/flowchrt.html.

Broan Model V60C-1 Motor?
Question:
Which motor brushes do I have to order for a Broan model V60C-1? How much is shipping of two brushes to Canada? Thanks! Edith, BC, Canada
Answer:
Hi Edith, based on number 6472-00 on the motor for your Broan V60C-1 the replacement brushes and motor are here http://builtinvacuum.com/retail/shopretail.php?part_no=210R,209.

Will Not Shut Off
Question:
I have a NUTONE CV450. The on off switch will not turn the unit on or off. The unit must be unplugged before it goes off.
Answer:
Hi, remove the low voltage wire from the unit and test again. If the unit is off then there is a short in that wire somewhere. Thease are hard to find and you may have to move to RF controls. But if the unit is still on then the relay is bad in the unit. We have this relay that may work for you as you consider the components and wiring in your unit http://builtinvacuum.com/retail/shopretail.php?part_no=242. We also have a circuit board for two motor systems here that an electrician can easily use to replace all the components http://builtinvacuum.com/parts/electrical-parts.html

Nutone 599 Question and Replacement
Question:
Janet (Massachusetts) I have an older model 599 powerhead that siezed up suddenly. I've removed all the hair build up. Do both ends of the brush rotate? One moves freely, the other appears stationary. I can't understand how one could be stationary. The system is by Pullman and the relay switch problem was fixed to the tune of $218. Most importantly, if I can't get the powehead running again, which powerhead is the replacement?
Answer:
Hi Janet, I think both ends of the brush rotate if the brush is not inside the nozzle head and the belt not attached. That is the way all the brushes I've seen work. The first three brushes here (Stealths and Blackhawk) are wonderful replacements for the 599. They fit right in. http://builtinvacuum.com/brushes/electric.html

Replace Motors or Unit?
Question:
I have 2 CV450 units in my home (8 years old). One is fine, the other needs a motor replacement. It has been recommended that I simply buy a new unit. Would you recommend another CV450 if I can find one, or a comparable but newer model that would be compatible with the existing tubing, etc. House sq footage is 4800 sq ft. Thanks Steve Lewes, DE
Answer:
Hi Steve, we recommend a different unit. The motor on the new Flo-Master M85 will be more powerful that the two motors in the 450. The cost is over $500 and it uses the same pipe and wiring. Use our dealer locator to find a dealer new you for a sale.

CV40 Models - New to Central Vac?
Question:
We have a Broan Model CV 40-D Central Vacuum in our new home. We do not have an operations manual. Where can we get a manual? Do we need to have a bag or is this a bagless model? If it requires a bag, which bag do we need? If it is bagless, what filter do we need? Thanks, Looking forward to using the central vac.
Answer:
Hi, congratulations on the new home and central vac. The CV40 has a center-weighted cloth filter that is semi-permanent - no collection bag. Releasing the bottom bucket and emptying it is the only maintenance on the entire system. You can put a trash bag up around the bottom and shake out the filter. If you want to clean it, remove it by grabbing a top side and pulling inward with some force. The stiff outer rim flexes and the filter falls down. You can vacuum it with a shop vac or hose it out and THOROUGHLY air dry it before replacing. There are not replacements for it. We have a filter but it is slightly too small and slips out of place. If some tabs could be added inside the metal can to keep it in place then it would work fine. For all the troubleshooting needs go here www.builtinvacuum.com/flowchrt.html and for your many instant upgrades to modern hose and tools start here http://builtinvacuum.com/help/nutone.html. Let us know if you have any questions.

VX475 Motor Overheating
Question:
Our 3-4 year old Nutone VX475 motor overheats, then stops. Do we need a new motor? Joan Jupiter, FL
Answer:
Hi, please contact Nutone directly for that issue. Hopefully you are under warranty.

Light but No Suction
Question:
My daughter stuck a coat hanger in the hose of her CV-750 cental vac to dislodge an onstruction and it quit working. I hit the rest and the light comes on but nothing runs. do I need a new circuit card or some component on the board? where can I get these parts?
Answer:
First use this guide to troubleshoot it backwards www.builtinvacuum.com/flowchrt.html. Then call us if you can't determine the issue.

No Suction at Unit
Question:
My Nutone CV-570 has very low suction both at the hose and at the unit. Is it possible that the cloth bag is clogged or do I have an impeller problem? The motor seems to run as usual. Mike
Answer:
Hi Mike, remove the bag and try the suction at the unit. It is rare for the motor itself to be clogged up. You are trying it at the unit without the hose, right? If not then it is the hose that is clogged.

Rewired, Pulses
Question:
I have a new cv850. Replaced my cv450 with a cv850. Problem is the light blinks on and off. Motor pulses on and off with the light. Sometimes motor starts all the way, but reset switch trips after 5 min or so. Very good suction. What could be wrong. I did rewire ciruit for 240 volt.
Answer:
The key is the minibreakers tripping. The motors are getting to hot. There is some kind of electrical issue and you should have it looked at.

Replace Broan V23C Motor or Unit?
Question:
Hi, I have a Broan V23C. 23 years old. Mtr has on it lamb 115334. Do you have a replacement motor? IF I wanted to replace the whole unit which model would fit or would you recommend. How much for motor? how much for new unit sent to Walkerton On. Canada? Thanks Ken
Answer:
Hi Ken, we have the motor here http://builtinvacuum.com/retail/shopretail.php?part_no=201. In checkout use the third button, the Canada Customers Checkout button and put in your address to get the final price for duties, taxes, etc. If you want a new unit we suggest the FloMaster M85 with 50% more power for double the cost of the motor. Please call us for that. Your call...

CV850 vs CV450 Nutone
Question:
I have 10yr old CV450. Brushes shot, so motor replacement seems appropriate. What is the most powerful motor repalcement available for upper and lower? Also, just got a new CV850 220v, its seems less powerful than my CV450 though quieter in the same installation (ie not a pipe problem). Is this possible ? Does it sound defective ? Any suggestions ? I'm going to get replacements motors for 450 anyway. Tx
Answer:
Hi, the CV450 is powerful because it is two motors in series. You need to use the given replacement motors. It will feel stronger but running motors in series is rough on them. The CV850 is more traditional in its set up and the motors are powerful and will last longer. Hope that helps!

Would Like Electric without Cord
Question:
Hi, We have a Nutone CV450w. Our vacume head does not have a beater brush and I was wondering if there is one that would work with this model that doesn't require me to plug in an electrical cord? How do we know if our hose carries an electric current? I dont want to have to plug a cord into an outlet to activate a beater brush. (too many cords/hoses) Thanks so much, Tricia Cape Cod
Answer:
Hi Tricia, let me try to sell you on a corded hose. The cord is nothing you have to carry around. The wires are hidden in the long lightweight hose. And you only have to plug in the cord if you wanted to use the electric brush. The cord comes out the very end of the wall end of the hose that plugs into the wall ports. It is eight feet long. So you need an electrical outlet within 8ft of your vacuum inlet. So if you paid the big bucks for a new electric kit (hose and tools) you'd have the cleanest carpets you ever had - guaranteed. The alternative would be to buy a TurboCat vacuum nozzle. It spins and grooms because the air passes through it and spins a turbine and it spins a belt. It works but is loud and can be weak. It depends on your suction. It fits the hose you have now (which is not electric because it would have a cord on the wall end or two brass pins). Here are the kits http://builtinvacuum.com/help/nutone/kits.html and here is the TurboCat http://builtinvacuum.com/help/nutone/kits.html#air (alone towards the end of the TurboCat products).

Nutone CV850 110-120 Volt Motors
Question:
I have a Nutone CV850 but it is 110-120 volts not 220 volts. Do you have motors for it?
Answer:

Some Inlets Not Working
Question:
I have a 13 y/o nutone cv-450w system in a recently purchased home. One of the outlets worked fine at first, but is now not working at all. Nothing comes on anywhere. Other outlets in the home work great, with the exception of this one and another that has not worked since we moved in. Please help.
Answer:
Hi, please remove the faceplate and short the low voltage wire so see it if starts. If so then replace the faceplate. If not then the line is broken somewhere. You can move to a wireless remote to turn the suction on instead. Call us for more information. It is not too expensive - around $200.

Broan CV30 Filter and Attachment Set
Question:
I just moved into a house with a Broan cv30 central vac...no user guide. Does it use bags? There is a cloth liner...do I just empty the can? Any tips on how to clean it and keep it in top condition would be helpful.I have never used a central vac and I imagine like any appliance, maintenance would be helpful to keep it in top condition. If it takes bags, what item number do I need? Also we have dogs...should I invest in a power hose in order to best pick up dog hair from rugs? Thanks, Lizanne - Rochester, NY
Answer:
Hi Lizanne, congratulations on the home and central vac. First, a new electric kit will make your home much cleaner and will get all that dog hair. We have several options here and they all work with CV30. We suggest an electric kit - the Stealth or BlackHawk for the best fit on the older Broan/Nutone square-ish wall outlets. http://builtinvacuum.com/help/nutone/kits.html. The filter is only a center-weighted cloth filter, that is it. You can replace it with this one here. http://builtinvacuum.com/retail/shopretail.php?part_no=711B. To remove simply grab a top edge and pull inward flexing the outer rim. As you get more into it please give us a call when you need help.

Relay Stuck?
Question:
Ron - Lodi - CV30-D problem - continously running. Disconnected low voltage, turn off switch on unit, still running. Appears to be relay/circuit board problem. I tapped relay, no change. Please indicate part number and price. thanks r
Answer:
Yes, sounds like your relay is stuck. The only stand along relay we offer is this one http://builtinvacuum.com/retail/shopretail.php?part_no=242 which may work. Take a look at the wiring diagram, the amps are fine with your unit.

Unit Stays On
Question:
Broan model CV30-D - I need relay, unit stays on - has to be unplugged to shut down. Have had same problem b4 - is it just relay? Please send price and order info. Thanks
Answer:
Hi, that is a low voltage or relay issue. Please troubleshoot it using this guide and let us know if you have more questions www.builtinvacuum.com/flowchrt.html.

Low Suction at Unit Tank - Bag Position
Question:
We have a NuTone CV850 Central Vacuum Power Unit, with a new bag on and the bottom tank connected, have a very low or no vacuum pressure. What is the probably cause for this type of symptom. Both motors come on, but still no vacuum pressure at the Power Unit Inlet. Your immediate help and answer will be appreciated. Jay Lewis Kentucky
Answer:
Hi Jay, if you put the bag in so it hangs down it can double or triple up on itself and have no suction. Put in the bag so it wants to expand up. If that doesn't help then remove the intake pipe coming from the home and test there at the unit. If bad then did you install the gasket around the motor (SINGLE MOTOR UNITS) or is the gasket between the lower and upper halves of the tank leaking? If the suction is good at the intake connection on the unit then it means you have a break somewhere in the pipe system and it is sucking in air. Any work done on the home recently? If a new home, maybe a joint came unglued? Hope this helps.

Dust Bucket Stuck
Question:
I am unable to remove the dust bucket from my Broan CV40 after unhooking the latches. Any suggestions for freeing it up? Does only the bucket come loose with the gasket staying on the upper assembly? Do I need to fold up the gasket? I think the bucket got too full. Ruth, Crofton, MD
Answer:
Ruth, you need to break the dirt seal. Use a hammer and screw driver to tap along the edges downward.

Replace Broan CV110
Question:
I have a 22-year old Broan CV110 Central vacuum system. The motor just burned out and I need to finish vacuuming the rest of the house! Can a replacement motor be ordered or can I replace the whole unit - after 22 years, I feel I got my money's worth.
Answer:
Hi, we highly recommend replacing the Broan Central Vacuum Model CV110 with our SilentMaster S2 or S44. Here is some information and links http://builtinvacuum.com/help/nutone/units.html. The vacuums are sold through local dealers. You will love the difference and the swap out takes no more than an hour.

Broan Model CV212 Central Vacuum
Question:
My home has a Broan Model CV212 Central Vacuum Unit that is 20 years old. I believe its a 220-240 with two motors in it. What type replacement parts do I need. Thank You
Answer:
Hi, we have the motor and hose and attachments for your Broan 212 system. You can start here or call us for help. A new electric attachment kit will be the best upgrade possible. http://builtinvacuum.com/help/nutone.html. What is it you are looking for in particular?

Nutone CV-450 Circuit Board
Question:
I have a Nutone CV-450. The relay is on a circuit board. The unit will stay on even when low voltage disconnected and on/off switch is in off. I tapped the relay and now it works. I just don't know for how long it will keep working. I would like to order a circuit board to replace the one I have. What one will work? Thanks, John Mesa AZ
Answer:
Hi John, you can use this circuit board for the central vacuum http://builtinvacuum.com/retail/shopretail.php?part_no=235M.

Vacuum Blowing Air, Not Sucking
Question:
All of the sudden our Nutone CV450 is blowing instead of sucking. What could cause this?
Answer:
Hi, please go step by step through this guide to find the problem and let us know if you get stuck or have more questions. www.builtinvacuum.com/flowchrt.html.

Exhaust Run Length
Question:
nutone 200 and 400, how far can the outside vac vent be from the main unit? thanks
Answer:
You should keep the exhaust run to under 20 feet and 15 feet is really the best maximum length.

Same Motors for CV450?
Question:
I have a Nutone CV450, last week the bottom motor burnt out this is the second motor to burn out within the time I have had this unit and it isn\'t four years old yet. When I first noticed the motor going I ordered a new motor but I thought since the bottom had already been replaced it was the upper and it wasn\'t. My question is I am now using two upper motors, will this work alright or do I need to get the bottom motor. Right now everything seems fine, good suction. Any suggestions what would cause two bottom motors to go out in such short time? Thanks Jack Ball Wallins, KY
Answer:
Hi Jack, it is okay to use the same motor for both. Really the only difference is the one has a neck on the bottom (you can tap off the bottom section of the motor and put on the new motor). The motors are ran in series on the 450 and 750 so the motors will go out more often. In exchange you get a lot of suction though. If for some reason you think a motor died too quickly, send it in for warranty review.

Nutone CV40 Top Motor
Question:
I have a Broan CV40 top mount system. It has two motors, one does not have a discharge pipe housing and the other does. The picture for the 119412 shows a discharge pipe housing. I can't find another motor on the site for the CV40 without the dicharge pipe housing unless it's the 119413. Does the housing come off when installed in the first location? Please help me order the correct motor. The motor that failed is the first motor without the discharge pipe housing. Thanks Dale
Answer:
Thanks Dale, looks like we need to fix the website. It should read that the uppermost motor takes the 119413 replacement (has no discharge tube but rather exhausts all the way around through small ports).

Nutone VX475 Central Vacuum Gasket Issues
Question:
I have a Nutone VX475 that in just over a year old. Recently, after disconnecting and reconnecting the debris bucket, the suction has declined. I believe the gasket between the bucket and main unit is not sealing properly and that I may need a new one. Can you help?
Answer:
Hi, the gasket may not be seated correctly as you suspect. Most likely it needs some detailed attention and is not broken. Please try attaching and realigning it and let us know how it goes.

Convert to Paper Bag?
Question:
have cv20, how do you clean cv20 filter cloth bag and can you get the paper filter bags? My inlet doesn't have anything to push bag on to. My wife sucked a nail polish bottle into the system any suggestions how to get it out? Thank you
Answer:
You can suck up paper towels to push the bottle through to the unit. The unit may be able to convert to paper bags if there is "pipe" exposed on the inside where the debris comes shooting in.This is how you would do it. Put a PVC Coupling on the plastic pipe that enters through the side. Add a Bag Adaptor to the Coupling and finally put a #723MF-5 bag on the Bag Adaptor. Attach the bottom dirt holder and you are done! Here are the parts http://builtinvacuum.com/retail/shopretail.php?part_no=507,726,723MF-5

Relay for Nutone
Question:
We purchased a Nutone CV-350W central vacuum system in 1998. It has done a excellent job. We are now in need of the relay that controls the motor. The part has an manufactures number of: YR91364UL. Can you help me? If it is avaiable, please let me know your part number and cost of it. Thank you Leslie Wolfe, Newark, OH
Answer:
Hello Leslie, if your relay has posts on the corners then you can use our #241 relay. See it here and click on the wiring diagram link in the description to see it wired. http://builtinvacuum.com/retail/shopretail.php?part_no=241

New Motor not Starting
Question:
Hello. We have an old HP Vacuflo 2, That has a new motor. When I lift the flap to plug in the Hose there is nothing happening. The power points are fine so it's not a fuse. The Vacuum isnt starting at all. HELP? kind regards, Kylie, Riverside Ill.
Answer:
Hi Kylie, do you hear a click at the unit when you open the inlet door on your proprietary Vacuflo inlets? If so then the motor is not getting power, if not then the relay is not working. Short the low voltage intakes at the VacuFlo and see if you get the click or not.

Replace Filter Screen?
Question:
I have a Nutone Model 350 central vacuum vintage 1970ish. There is a screen filter between the bag canister and the motor. do you sell replacement filter screens?
Answer:
Hello, we don't have the filter screen and that model has long been out of production.

Motor for CV550 All Models
Question:
I am in need of a motor for a Model VX550C. Can you help me on this?
Answer:

Motor for Nutone 350
Question:
hi, i have a nutone model 350ca central vac ( not sure what year ). I\'m looking for a replecement motor. Can you tell me the model i will need and a price please. Thanks, andy
Answer:
Hi Andy, please click here to see your two options: http://builtinvacuum.com/retail/shopretail.php?part_no=201,207.  Just choose the one that looks like the one in your system (#201 is for older model 350's)

Nutone 351 Needs Motor
Question:
my nutone 351 needs a motor is there a cross? Larry
Answer:
Hello Larry, please look at our motor cross reference for Nutone 350 and decide if one of those motors matches your current motor.

Motor for Nutone Model 351
Question:
On the replacement motor chart I don't see a replacement for a Nutone 351. The motor on the unit is a Singer MB22? Is the a cross for this motor? Larry Carson Valley, Nv
Answer:
Good Afternoon Larry, We do not see a reference to this model # either.  Please take the motor out of your vacuum system and read us the #'s located on that motor.  Once you have that information, please contact our offices at 1-800-997-2278 (M-TH 7-5 PST).

Broan/Nutone Inlet Valve
Question:
I have a Broan Central Vac, Model CV30. Is there any place in or near Valparaiso, Indiana to purchase this part? If not, is this part available to purchase anywhere? Thank you, Donna Kuehl
Answer:
Good Afternoon Donna, please click our Dealer Locator http://builtinvacuum.com/find-dealers.html and enter your zip code.  You may also purchase this part online or call our offices at 1-800-997-2278 (M-TH 7-5 PST).

Nozzle Neck Connection
Question:
I have a Nutone 598 with a broken lower wand to vacuum head hose coupling. This part connects with the wand, wheels and short hose to the head unit. Can I get a replacement part? Otherwise the head is still in good shape.
Answer:
Your carpet brush is broken and we don't have that part to fix it; and since it has not been produced in years you may not be able to locate it. Sorry. Nutone customers have bought the Stealth or Blackhawk nozzle to replace the entire head. http://builtinvacuum.com/brushes/electric.html

Replacements for Broan CV 40-B
Question:
I am looking for the following replacement motors for a Broan CV 40-B Central Vac; 1- 99080344 UPPER MOTOR 1- 99080233 LOWER MOTOR ALSO; 1- 99010174 filter BAG 1- 99100452 MOTOR GASKET 1- 99100453 GASKET
Answer:
Hello, the first two items, the motors, are http://builtinvacuum.com/retail/shopretail.php?part_no=206G,202G,how2mtr, but we do not have the filter or gasket.

New Vacuum Nozzle for Nutone 598
Question:
I have a nutone model 598 with a worn out beater bar. Where can i get one? Thanks. mark; Karlin, Michigan
Answer:
Hello, typically the Eureka/Beam is used to replace nozzles with an electric cord. If no electrical cord, use the Turbocat www.builtinvacuum.com/retail/shopretail.php?part_no=482,455

Dealer in our area?
Question:
Can you supply names of installers in the Easton Pa 18045 area. I believe we need our 25 year old motor replaced. It just stopped running. We are having the same trouble as another writer. Circuit breaker pops after about 3 minutes. TED
Answer:
Hello, there is a dealer about 20 miles away from you. They are called Flagship systems, and they are located at 35 Sylvan Road, High Bridge NJ, 08829. Their phone number is (908) 638-3296  
   
   

Will Not Turn Off - Relay?
Question:
bryan, valley mills texas i have a nutone centrl vac unit MODEL CV353W will turn on but will not turn off - you have to unplug - i checked continuity on low voltage wires ok, on/off switch ok but relay seems to stick on wont go off - i could not find relay to repace original #yr91364ul AUGAT 120 VAC CAN YOU give the correct part number thank you
Answer:
Hello, please disconnect the low voltage wires from the unit and plug the electric cord back in. If it runs then you need a relay. If it doesn't then you need to find the short in the low voltage system running through the home and to the inlets. That relay is no longer available. You can see about retrofitting our #241 though. We have other suggestions too if you call us.

Relay for CV400
Question:
Re: Nutone CV-400 Vacuum I need a stand alone relay swithch. Where Can I purchase one? Ed
Answer:
Hello Ed, you may be able to use our #241 Relay. See it here and click on the wiring diagram link in the description to see it wired. http://builtinvacuum.com/retail/shopretail.php?part_no=241

Relay for CV353 Nutone
Question:
Do you know of a replacement isolation relay for a Nutone model CV-353. The relay says ALCO model FR 110 rated at 10 amps and 120 volts. I can't seem to locate one? Thanks, Dennis Olympia,Wa.
Answer:
Hello Dennis, doubtful you will find it. You may be able to use our #241 Relay. See it here and click on the wiring diagram link in the description. http://builtinvacuum.com/retail/shopretail.php?part_no=241

Turns Off, Reset Button
Question:
I have an older Nutone system (at least 15 years old) in our 4000 sf house. The system works well, but shuts off after about 10 minutes of use (I'm assuming because the motor is hot?) and I have to push in the reset button at the top of the canister. Does the motor need replaced? There is no model number on the unit that I can find. Where can I locate the model number?The canister is red. Thanks, Anne
Answer:
Hello Anne, yes your motor needs replacing. Look for the model number on a plate near the reset button. If you can't find it you can use your motor and its measurements to find the exact replacement on our website.

Removing Cloth Dust Bag
Question:
I asked how to change dust filter on Broan CV30-D. You gave instructions. I found our booklet, it says and shows picture but thats not the case on this. The bag feels like it is glued or sewn to the inside of the bucket, no hold to get a hold of it to release anything and get a bag out. We have all but climbed inside to see no clamp of any sort holding it. I would rather not cut the bag off but can't see how it is in there. I have pulled and pulled, shouldn't be this hard to deal with a dust bag. Thanks. Jill Brinnon Washington
Answer:
Hello Jill, you have the cloth inverted filter that is weighted in the center, right? Those all come out by grabbing the cloth at the top near any edge and pulling directly toward the center. It may be difficult but that is how it works. Just to note: if you are going to change the vacuum unit, consider a top emptying disposable bag unit such as the SilentMaster. Your bag is easy to remove and replace. There is less or no dust inhaled in the process and all the dirt from your last vacuuming months is forever gone - no plastered to a 5-year cloth filter.

Need Bags!
Question:
Hi. We just moved into a house with central vac model CV40-D. We were wondering where can we buy replacement bags? Thanks, Nancy
Answer:

Need Bags, That's it.
Question:
I just want to buy bags for my Nutone machine. No local vendors seem to carry them and have even told me they are no longer available.
Answer:
That was simple, we have replacement bags right here http://builtinvacuum.com/retail/shopretail.php?part_no=723 

Clog and Cloth Filter Issues
Question:
We installed a Broan Central Vacuum System Model CV30-D in 2000 in a house we were building. Some plasterboard and larger stuff got sucked up and it hasn't worked very well since. My other problem is this: Can you replace the filter that is hanging in the middle after you release the dust canister? It is so clogged I have to shake it around then empty the can. Very messy. My husband has tried to remove the filter but doesn't seem to be able to, short of cutting it off there and putting a hose clamp on a different style. thanks. Jill Brinnon
Answer:
Hello Jill. We are sorry to hear of the clog. Do all of the inlets have low suction? The clog will be between the Nutone and the first port with low suction. You can suction the port hole or use a thin snake. Use a paper towel wadded up, put your ear on the wall and count the number of thumps you hear, that is how far away the clog is. Worst case is you will have to open up the pipe. You will hear the clog because it is clanging with debris. For the filter - pull from the top edge towards the center and the filter will release down. If you need a new one that has a 14" diameter, just search our site for "inverted".

How to Change Filter
Question:
how do you change the filter
Answer:
Typically in most Nutones that are not the color Red, but are white and made of metal not plastic, the bottom bucket is unlatched and the bag is taken off the intake neck. It is that simple.

Cloth Filter for V20C Broan
Question:
I have a Broan V20C and I need a new filter. Any idea where I could get one?
Answer:
It has the inverted cloth filter with the weighted center, right? Measure the diameter of the where its outer metal flex ring is held in. We have bags with 11.5" and 14" diameter in the Cloth Mesh Foam section under Bags & Filters, parts 710B and 711B.

Power Vent Central Vacuum
Question:
Our canister says "Power Vent" though our outlet says "Nutone" Is "Power Vent" an older version of nutone? If so, can we get parts for it? Specifically we need the felt filter with rubber gasket that hangs above the filter bag in the canister. Thanks
Answer:
Power-Vent is not a real known vacuum, may be a private label. It may have been a Vacumaid. I doubt you'll find that filter exactly but if you measure the diameter it fits into you can use a foam filter, used in many central vacs, that is found here http://builtinvacuum.com/bagsfilters/cloth-mesh-foam.html. You can cut to size if need be.

CV570 Cloth Bag Issues
Question:
Hello: I have a Nutone model CV570 I believe it is about 3 yrs old. (We just bought the house) I removed the bottom of the canister and can empty the contents. I can see the cloth bag in the upper portion. It feels full of dust and sediment but I can't seem to get it to come out. What's the trick? Is there some sort of snap-ring or other clip holding it on? How do I get it off? Also, once you tell me how to get it off, Is there a filter replacement needed?
Answer:
Your cloth bag should feel that way. It is packed with weighted stuff so that when it turns off it will go from an up position to a down position...helps clean it off. You will probably be fine with that bag for many years. To clean it, take the bottom off, wrap a trash bag up over it and then give the bag a good shaking. When ready to replace we have a 14" and 11.5" wide cloth inverted filter. That may or may not work for you.

Low Suction
Question:
My 18yr old Nutone CV-400 vacuum has lost a lot of suction, but not all. When I manually turn it on in the garage and put my hand over the outlet there, it has only a little suction with no "wind up" to build a vacuum (no change in motor sound). Then I let go and there is only a short little "rush" of air. I see that it has two identical motors. If one motor is not working, is there a way to tell w/o taking the top off? The cloth filter above the bag looks in good shape. If I turn on the motor, then slowly put the canister back on, it sucks it up very solidly.
Answer:
You'll have to remove the lid to check if a motor is bad. Both may look like they are spinning so you want to test them individually by disconnecting one of their wires. Have you done any work on the home? With no "build up" up of suction it almost sounds like a pipe is broken or something like that. But with the 2-stage motor, and only one working the build up would not be too huge anyway. See what you can find.

Sometimes Suctions, Sometimes Not
Question:
I have a Broan V28C-1 central vac that's 10 yrs old. Sometimes it will not turn on, neither by plugging in the hose, nor from the switch on the unit. Other times it works just fine. When it works, I notice a grinding sound in the motor when it first starts up, but that goes away in a few seconds. When it's not working, I have tried pressing the circuit breaker reset on the unit, but it still doesn't turn on. I have verified that there is power going to the unit. I have also checked the connections to the transformer, the relay, and to the motor. All connections are fine.
Answer:
Sounds like your motor is going bad. Here is what you need to fix it.

No Suction at Hose
Question:
My main unit in the garage works very well when I turn it on in the garage. However, when I run the vacuum in the house and turn the switch on at the handle of the vacuum, the rollers turn but the main unit in the garage is not getting the signal and is not turning on therefore I am not getting any suction. Your trouble shooting chart does not touch on that subject nor does your FAQ. Can you help?
Answer:
Use something metal to short out the two contacts inside the LARGE HOLE of the vacuum inlet wall valve. You will not get shocked from the low voltage protrusions. If it turns on then your hose is at fault. If it doesn't turn the suction on then their an issue with your low voltage wiring that runs back to the vacuum unit.

Replacement Unit
Question:
I have a Broan Central Vacuum cleaner Model V16. This unit is about 25 years old and the motor has stopped working. Can I just buy a new Vac with out having to purchase all the accessories? ie new canister complete with motor, my hoses etc are all in good working order. Thanks Carolyn
Answer:
Yes, you can buy the unit or upgrade it with a powerful and quiet SilentMaster. We offer the SilentMaster, not the Nutone units.

Will Not Shut Off
Question:
My daughter has two dogs and uses her CV450W vac quite a lot. Last week she called and told me it wouldn't shut off. There are 5 outlets in the house and I thought maybe one of them was broken or damaged. I disconnected one at a time and it still ran. My question is, Is there a relay inside that is keeping it running and could I replace it easily? Thank You Bill Hartford
Answer:
Please disconnect the low voltage leads and see if it can turn on and off with the canister switch. If it does, your low voltage wire has been shorted somewhere in your home. If it stays on then you do need a new relay.

Bagless Nutone How To
Question:
I have a bagless nutone central vac. I can take the canister off and clean it but the filter i am unable to get off to clean is there a trick to taking it off?
Answer:
Grab the material up close to where it is "stuck" to the canister and pull towards the middle. This will flex the metal ring inward and the cloth will drop out.

Take Off Cloth Filter
Question:
We moved into our house in may this year and it already had a nutone central vac. I don't know how to take off the cloth bag. I can get the canister off but not the bag or filter to clean it out. How does it come off?
Answer:
Typically with most Nutone models you leave the unit on the wall, take the bottom off and remove a paper bag.

Broan/Nutone Top Motor
Question:
I have a Broan Central Vac, model CV-40C. There are two motors on top. The suction motor works and the exhaust(?)motor does not. With out taking the exhaust motor out, the only numbers I see are Lamb 6392-01 and 660296F. Which of your replacement motors is the one I need? and is it called an exhaust motor? Thanks
Answer:
It is actually pulling air from the lower motor and increasing the amount of suction you have. They both exhaust out the top motor. This motor fails because it runs hot from the lower motor's exhaust. Here is the correct replacement motor.

Will Not Turn Off
Question:
I have CV353W central vacuum. My power unit does not stop working even after I remove the hoses. Has the relay gone bad? how does the relay look? Is the relay same as the switch at the power unit? Do you have a picture of the relay? What could be the other problem areas. If necessary do you guys come and take a look at it? Thanks Simha
Answer:
You will discover the problem using our easy to follow troubleshooting guide.

Need Smaller Budd Inlets
Question:
I need two 1.25" wall ports for the Budd central vacuum system. My mother-in-law already has 3 outlets and a 1.25" hose. She is adding a small addition and needs two more outlets (upstairs and basement). She does not need a new hose and the other 1.25" outlets work fine. Can I get two ports to put in the new construction?
Answer:
The non-industry standard sized inlets from Budd are still available. Please Google Budd Central Vacuum for their phone number.

Nutone Rplacement for Part #44902
Question:
I have a cv-400 unit that needs a motor . The Nutone part # is 44902 REB. What is the motor on your site comparable to this NUTONE part #?
Answer:
The motor 119412, as indicated on the motor section on the Nutone Help Page, is the best replacement motor we have for this. We have sold many to homeowners and have had excellent results.

Nutone Lower Motor Upgrade? NO!
Question:
I only need to replace one of the motors (lower) in my Nutone CV450 Your ad says (If you want a stronger motor that will fit in its place, order the 116472). My question is: Do I have to replace both upper and lower motors at the same time. Will the vacuum work promptly with one motor stronger they the other?
Answer:
Great question. Glad you asked. The answer is no, on the Nutone units with motors in series such as yours, you must not upgrade any motor. It will upset the delicate balance and destroy both motors.

Broan CV30C Motor Replacement
Question:
Is the 117507 motor the only one that will fit on a Broan model CV30C
Answer:
In the reference chart you can see the two options that were offered with that model. A quick visual comparison to your existing motor will get you the right one for your system.

Troubleshooting
Question:
My CV-450 unit is 12 years old and stop working. There is elec. to the unit but it doesn't run. Do you have trouble shooting instructions? Thanks Doug Sensenig
Answer:
We have a fantastic troubleshooting guide. Start here and let us know if you have more questions.

Assemply Diagram?
Question:
how to reassemble (diagrams) a nu-tone cv-450 vacuum?
Answer:
We don't have step-by-step instructions. Would a photograph of an assembled motor / wires / electronics help?

Nutone CV450 Motor Sparks
Question:
NuTone CV-450: Breaker pops out after just a few seconds of operation. Appears the brushes on the top motors are arcing, lots of sparks. Bottom motor looks OK. Is motor causing this or bad breaker? Thanks
Answer:
This is a sign the motor is dying. The sparks are the motor brushes arcing to the armature core of the motor, it will need to be replaced.

Nutone 391 Motors
Question:
My nutone is a CV450C model 391, 12.5 amp. 115-120 volt. what motor do I need to order, it is the main motor. will your 116472 do the trick?? please advise, I do not want to order the wrong one. thanks Richard Wolynec
Answer:
The Nutone CV450C takes two motors and the top one is different from the bottom. You can find both replacments here, http://builtinvacuum.com/help/nutone/motor.html#filter Just scroll down to your model number.

Ask your question below:
Include your first name and city if you don't mind, thanks!
characters left
Please note that your question will not immediately show on our site, but will show as soon as we answer it. We typically respond within 48 hours.
Please enter your email address and we will email our response to your question:
 


Need more help? Try our extensive and helpful Nutone Vacuum Questions and Answers or give us a call at 1-800-997-2278 M-Th 7 a.m. to 5 p.m. Pacific Standard Time.
 
*Note: Nutone Vacuum is a registered trademark of Nortek, not M.D. Manufacturing, Inc. Products sold by M.D. Manufacturing, Inc. are not from Nutone Vacuum but are designed to complement a Nutone Central Vacuum. Therefore, parts and products carry warranties from MD Manufacturing and not Nutone Vacuum and thus may alter the warranty provided by Nutone Vacuum.