Click here for a list of replacement hoses for all central vacuum systems.
Click here to find your replacement hose by brand name. Click and view brand list on right side.
|
 |
^Click to enlarge. |
Hose Cuff with Metal Ring Part#302HCR
Cuff screws onto the corrigations of the Basic Hose (counter-clockwise). Also very helpful when used alone to maintain a central vacuum system. When inserted into a vacuum inlet the suction starts right away so it is easy to test all the inlets and to cuff with the hand to build pressure in the system in order to help clear out debris and clogs. The insertion end is just under 1-1/2" wide OD, and the screw-on end is 1-7/8" wide OD.
|
|
^Click to enlarge. |
Tapered Cuff - Inlet Valves 1.5+ Inches Diameter Part#302CT
Tapered Cuff screws onto Basic Hoses (ones without a switch on the handle) and slips onto the end of Electric, Low Voltage, and Stretch Hoses. It then fits valves slightly larger than 1.5" diameter such as Filtex metal inlets, some AstroVac, VacuMaid, and others. This cuff will not work with valves having two metal contact points inside the inlet insertion hole. Basic Hoses #302TC and 303TC ship with this cuff included. Tips for installing on a Basic Hose.
|
|
^Click to enlarge. |
Reduced Tapered Cuff for 1.25 inch dia. inlets Part#302-1.25A
Reduced Tapered Cuff screws onto hoses - those without a switch on the handle. The cuff fits into 1.25" wall vacuum outlet valves such as Budd, Whirlpool, Black and Decker and Sears. Hose #302RC and 303RC ship with this cuff included. Plus, this cuff installs easily on any basic hose.
|
|
^Click to enlarge. |
Hose Cuff with Metal End for Basic Vacuum Hose Part#302HC
For replacing the all metal end on a central vacuum hose.
|
|
^Click to enlarge. |
Nutone Style Hose Wall End Part#300NMCA
Fits Nutone wall inlets that are square or rectangular. Adaptor screws onto all Basic Hoses and slips over the existing wall end of all Stretch, Low Voltage, and Electric Hoses. Suction begins when end is inserted into the inlet. NOTE: Low Voltage and Electric Hoses may have to scrape a bit of hard plastic off the two ridges (on the wall end of the hose) to get the perfect fit (if too tight) -retaining the on/off switching of the hose.
|
|
^Click to enlarge. |
Curved Wand Vacuum Hose End with Swivel Cuff Part#302WCG
For replacing the hose end on a hose without any on/off switches on the handle. Threaded trough is 1.75". There is not a button locking nipple on the metal stub tube, they don't make that any more. Instead, use two #406 wands or one $406T wand with this part. More info.
|
|
^Click to enlarge. |
6-inch Adapter cord to lengthen power brush cord Part#480AC
This 6-inch cord is used to adapt any electric power brush cord to fit into the plastic channel of the Cord Channel Upper Wand part 406SU or Telescopic Wand part 406ST. The upper wand will then be ready for any of the Electric Hoses to go directly into it - conveniently connecting both the electrical prongs from the powered carpet brush and the wands to the hose handle. This cord fits 3-prong cords because the third prong is not neccessary.
|
|
^Click to enlarge. |
35-foot Electric Cord for Electric Power Brush Part#302CO35
Use this cord to connect an electric power brush to a non-electric hose. Simply plug one end into an electric outlet near the vacuum wall inlet and the other end into the vacuum head cord. You will also need a hose sock to keep the cord beside the hose and you will need an new lower extension wand with button lock (#406SL)to keep the power head connected.
Female end is 5/8 inch wide and about one inch long.
|
|
^Click to enlarge. |
Generic 6ft Cord for SuperVac Hose IVORY Part#342COI
Use this cord to easily convert any of our Hayden SuperVac hoses into a corded hose that you can plug into an electrical outlet (instead of an electric vacuum inlet valve). The electric prongs on the hose can easily be changed to come out the other side where you will connect this cord and plug it into an electrical outlet. Also replaces existing cord on wall end of Hayden SuperHose all models. (Also fits Kenmore PowerMate.)
|
|
^Click to enlarge. |
Hayden Vacuum Hose Switch Replacement Part#342S
Hose handle switch for the Hayden brand central vacuum hose.
|
|
^Click to enlarge. |
Gas Pump Handle for Vacuum Hose Part#352GH
Replaces the handle and short metal tube on hoses with a gas pump handle design exactly as pictured. Does not include switch or wires but requires switch that rocks left and right not forward and back. Fits all Electric Hoses on this website (except 342(G) and 343(G), and is not compatible with Beam hoses but everyone can (upgrade to a better hose here.)
|
|
^Click to enlarge. |
Switch Assembly for Gas Pump Handle Part#352GS
SHIPPING AROUND FIRST WEEK OF JULY 2008
Replaces the 3-way switch assembly in hose handles that look exactly like the one pictured in Part# 352GH.
|
|
^Click to enlarge. |
Pistol Grip Handle for Vacuum Hose Part#352H
Replaces the handle and short metal tube on hoses with a pistol grip handle design exactly as pictured. Length is about 14 inches. Does not include switch or wires but requires switch that rocks left and right not forward and back. Fits all Electric Hoses on this website (except 342(G) and 343(G), and is not compatible with Beam hoses but everyone can (upgrade to a better hose here.) More info.
|
|
^Click to enlarge. |
Switch Assembly for Pistol Handle Part#352S
Replaces the 3-way switch assembly in hose handles that look exactly like the one pictured in Part #352H. Item is about 14 inches long.
More info.
|
|
^Click to enlarge. |
8ft Cord for Electric Hose (cuff and plug cord) Part#352CO
This is a hose conversion kit and replacement kit. Replaces the two prong direct connect assembly or an existing broken cord assembly on electric hoses with an electrical cord on the wall end. The two included cuffs cover an older or newer hose. Includes two cuffs, cord (with molded-in fuse), one male pin connection, one female slate connection (older hoses have two male pins and will need to be converted using the female slate connection - splice it into one of the wires from the hose under the cuff), and instructions.
|
|
^Click to enlarge. |
Fuse Plug for Electrical Hose (cuff and 2-pin plug Part#352CP
This is a hose conversion kit and replacement kit. Replaces the pigtail cord assembly or an existing broken assembly on electric hoses with an electrical 2-pin direct connection on the wall end. The two included cuffs cover an older or newer hose. Includes two slide-on cuffs, one 2-pin plug (with molded-in fuse) with one male pin connection (to connect to the yellow hose wire) and one female slate connection (to connect to the white hose wire), instructions and tiny slat to convert the white wire from pin to slat (older hoses have two male pins instead of the modern one pin, one slat configuration).
|
|
^Click to enlarge. |
Full Switch Assembly for Low Voltage On-off Hose Part#382S
The switch, entire switch assembly and wires are included - not the handle. Used in Low Voltage on/off switch hoses that control the vacuum suction and not an electric power brush. Note that #382H fits this by easily unsnapping the grey plastic of from the black switch. (Older, pre-1999, low voltage hoses will require splicing in the older contact board or special ordering Plastiflex #SH130efhr01.) More info.
|
|
^Click to enlarge. |
Handle for Low Voltage On-off Hose Part#382H
Comes with the metal stub tube coming out of the hose handle. The metal stub tube does NOT have a button lock nipple (only available on complete Low Voltage hose 382BL and 383BL). This part is used on Low Voltage hoses including MD's part # 381, 382, 383. Note that #382S fits it after removing the grey plastic portion away from the black switch. More info.
|
|
^Click to enlarge. |
Hose Cuff for Low Voltage On/off Hose Part#382HC
|
|
^Click to enlarge. |
8ft Electric Cord for older electric hoses Part#320
8-foot electric cord replaces some older detachable ones on electric hoses. Replaces cord with rectangle face and U shaped prongs. Pictured are the cord ends. The female end is about one inch long by 3/4 inch wide.
|
|
^Click to enlarge. |
Cord for Stealth or Central Vacuum Cleaner Part#49054
Not only is this a replacement for the Stealth Vacuum Cleaner(Part # 154 in the Stealth exploded diagram), it is also a good replacement cord for many central vacuum cleaners. On Stealth, the black wire goes on the right side when standing in front of the Stealth.
|
|
^Click to enlarge. |
Central Vacuum Hose Coupler Part#302C
Connects two pieces of vacuum hose together for repairs or to create one hose out of two. The vacuum hose can be 1 3/8 inches or 1 1/4 inner diameter and must not have on/off switches.
|
|
^Click to enlarge. |
Central Vacuum Hose Slip Cuff Part#302SC
 6 Reviews - 0 Comments Connects a vacuum hose to the cuff of another vacuum hose to create one hose out of two. The vacuum hose needs can be 1 3/8 inches or 1 1/4 inner diameter and must have no on/off switches.
|
|
^Click to enlarge. |
Central Vacuum Wireless Remote Control (RF) Part#145
This is the easiest way to bypass damaged low voltage wiring and remotely start the vacuum unit from within the home. Simply attach remote on the vacuum hose handle and other components near the vacuum power unit. And surprise - your low voltage troubles are over.
Range is similar to a car's remote lock/unlock device used with most cars today - about 150 feet depending on how many walls and the type of walls it needs to pass through. A small device plugs into electricity and hangs near the vacuum unit and wire attaches to the vacuum from it. Use the remote clicker to activate the vacuum on and off - it couldn't be more simple. PDF of Instructions
|
|
^Click to enlarge. |
Switch for Electric Hose, no suction control. Part#322S
This switch and circuit board is for an older electric hose that controled the electricity to the power brush, but NOT the suction. With this hose, when you plug the hose into the wall the suction would start right away.
|
|
^Click to enlarge. |
Low Voltage Booster Box Part#140LV
Splice this booster into a vacuum's low voltage wiring system, plug it into 110 volts, and your 24 volt line will be boosted with plenty of juice! The two blue wires connect to your power unit low voltage (you can use speaker wire to extent any of the wire here) and the red and yellow (or two red) wires connect to the low voltage leads coming from the home. You can hang the box on your wall with a nail into a stud. Be sure to use wire nuts to get good connections as you join the wires together.
|
|
^Click to enlarge. |
Low Voltage Hose Bleeder Cover Part#382BV
2 Reviews - 0 Comments Replacement bleeder valve hole cover.
|
|
^Click to enlarge. |
Electric Hose Bleeder Cover Part#352BV
Replacement bleeder valve hole cover.
|
|
^Click to enlarge. |
Button Lock C Clip Part#300B
 2 Reviews - 0 Comments This is used to replace a button lock on an extension wand or to create your own.
|
|
^Click to enlarge. |
Adapter for 3-prong cords. Part#352GBA
Adaptor fits on 3-pin power brush cords (that are not manufactured any longer) and fits into a new 2-pin-hole hose such as the modern Electric Hose #351, 352, 353. This adaptor comes with the "Electric Hose for Beam".
|
|
^Click to enlarge. |
EdgeLift , UltraLift and Essco Neck Replacement Part#469E5A
Replacement neck fits all brushes that look like the one on this page. This page also has video on how to replace the neck. How to Video
|
|
^Click to enlarge. |
Metal Stub Tube - Inlet Valves 1.25 Inch Diameter Part#302-1.25ST
Used to adapt a hose to fit Budd or Kenmore / Sears inlets and others that are 1.25 inch diameter (ones that start suction upon OPENING). This adaptor tightly slides into the end of the hose leaving the tapered end visible (we recommend tapping it in with rubber malet or piece of wood). It fits into all Low Voltage, Electric Hoses, and Stretch Hoses. If it needs to go into a Basic Hose, it will only fit the Basic Hose with Tapered Cuff. (Note: the Reduced Tapered Cuff product is made up of the Tapered Cuff and this Metal Stub Tube.)
|
MD
Videos
9110 Reviews
