MD Central Vacuum
Fast Free shipping
on orders over $75
Since 1961

Motors for Fasco 852SVDM

119413 Lamb Motor

119413 Motor for Vacuums and Blowers

Product Details

119413 Lamb Motor
Our brand new (not rebuilt) Lamb 119413 Ametek motor is a very common motor in many central vacuum brands and models. 119413 motor is a Lamb Ametek original motor.

Specifications:
  • Fan Stages - 2
  • Bottom Diameter - 5.7"
  • Voltage - 110-120
  • Hertz - 50-60
  • Height - 6.5"
  • Bolt Height - 2.75"
  • Waterlift - 84.9"
  • CFM - 97
  • AirWatts - 255
  • Amps - 7.4
What to note: This 119413 vacuum motor may say 9413 or 11-9413. Includes a wire set with spades to connect to motor. We recommend splicing the other end to old wire using wire nuts.

What motors it replaces: 116471 and 116336

When to replace: The signs that a 119413 Lamb motor needs to be replaced include: mini breaker popping, electrical smell, excessive blue sparks seen from motor top, you only hear a click, motor shuts down on its own but works later, or its life of 900-1,200 hours has been used up. (If you don't hear a click, then your relay most likely needs to be replaced and your motor may be fine). Five percent of the time, the minibreaker will go bad as well as the motor. If this happens, replace the motor and then evaluate the mini breaker.

How to replace: It is not difficult to replace the 119413 ametek motor. There are three to four screw brackets and a couple of wires. All of our customers are amazed at how easy it is. NOTE: There is no core trade-in. Used motors are thrown away. Click here to read and print out our step-by-step motor replacement instructions. Note that if the unit bolts into metal brackets then the ground wire can be snipped. If plastic then attach the ground wire to the ground from the power cord or anywhere to metal on the unit.

Replacing motor brushes: The lamb 119413 vacuum motor has carbon motor brushes that can be replaced. This should be done before a motor is "on its last legs." Read more about changing the motor brush on the detailed motor brush how-to page. If you are ready to replace your motor brushes, here is a link to the 119413 motor brush. You will need to buy two.

Buying Options / Reviews

$94.00 Part #202G
QTY
In Stock
Additional Items
119413 119412
119413 119412
$7.99 - In Stock

More Information
QTY
5.7 Inch Motor Gasket
5.7 Inch Motor Gasket
$2.90 - In Stock

More Information
QTY
Free Flow Maintenance Sheets
Free Flow Maintenance Sheets
$19.99 - In Stock

More Information
QTY
 

5.7 Inch Motor Gasket

5.7  Inch Motor Gasket

Product Details

5.7 Inch Motor Gasket
The purpose of a gasket is to prevent metal to metal contact when bolting in the motor. When replacing a motor you may or may not need to replace the gasket. Some units have quite differently shaped gaskets that are more functional that must be reused. PLEASE NOTE: if your original gasket is a larger form fitting gasket, then REUSE this original gasket to prevent damage to components.

Buying Options / Reviews

$2.90 Part #221
QTY
In Stock
 

Weighted Inverted Cloth Filter 14-inches Wide

Large Inverted Cloth Bag 110345 by Gore-Tex

Product Details

Weighted Inverted Cloth Filter 14-inches Wide
14 Inch diameter center-weighted inverted cloth filter for ALL central vacuums is approximately 14 inch wide, flexible sewn-in compression rim, weighted middle, and about 9 inches tall when relaxed (and lot longer when pulled). The circumference is of the outside of your vacuum unit will be about 44". NOTE: If the recess rim it snaps into is wider than 14 inches this filter will not work (some Beam and some Nutone regardless of cross references found on this site). Also replaces bag 110345, 110340, and 110341 and fits Beam 294, 289, 387, 397, 697, 2100, 2200, 2250, and 2500. To remove, grab top side and pull to center (or use screw driver to create a gap). Outer rim flexes in and the filter falls down.
Sold individually.

Buying Options / Reviews

$51.12 Part #711B
QTY
In Stock
Additional Items
Free Flow Sheets
Free Flow Sheets
$16.99 - In Stock

More Information
QTY
Mesh Filter
Mesh Filter
$9.74 - In Stock

More Information
QTY
 
How to Replace Most Central Vacuum Motors

SELECT THIS TEXT. COPY & PRINT IT FOR REFERENCE.

NOTE: Lamb Ametek Vacuum Motors are in nearly all central vacuum brands. The motors sold here are new, genuine Lamb Ametek replacement motors.

  1. Unplug the vacuum unit from the wall. If it is hard wired turn off the circuit breaker.
  2. If the motors are on the bottom of the unit take the unit down, remove debris bag, and turn the unit over. Disconnect the low voltage wires, if needed. They are small wires that follow the PVC pipe to the unit.
  3. Gain access to the motor compartment. (If motors are on the bottom, there is usually one screw on the bottom and/or one to three screws on the side.) Usually the motor shell will not come completely off but can be moved enough to easily access the motor(s).
  4. Notice the two or three wires coming from each motor. Disconnect each of the motor wires, or cut them in the middle where you'll later splice the new wire using a wire nut.
  5. There are usually two or three bolts, screws, or springs holding the motor down. Remove.
  6. Lift the motor out. There may be a gasket so lift with some force. If the motor has an exhaust port, slide it off or unscrew the bolt. Save it or buy another Motor Exhaust Coupling #507EX .
  7. If needed, clean off the old gasket from the motor compartment and place the new gasket on the motor with the sticky side on the motor. PLEASE NOTE: if your original gasket is not a thin foam pad they REUSE your original gasket no matter what.
  8. (Before anything is done with the motor check to see if it compressed in shipment. Reach a finger in and spin the fan. Listen for any scraping. To correct, use a screw driver to push the seam of the motor shell down a hair.) Place the new motor where the old one was taken out.
  9. Screw, bolt, or reattach the mounting.
    ***Do not use excessive force or the motor fan housing will move causing the fans to hit the housing when spinning. The seam on the side can be tapped down with hammer and screw driver if needed.***
  10. Connect the motor wires. There will be two blacks or a black and a white. The motor will run the same no matter if colors match or not. So don't worry if there is not a white wire to match a white (or black for black), just connect them. Splice the new wires to the old with wire nuts, or use connectors to plug the wire directly on. The green wire is a ground and if your new motor has one you need to connect it to a bolt somewhere on the unit.
  11. Plug the vacuum in and turn on the manual switch (or use the hose in the home after connecting the low voltage wire to the unit). The motor(s) should start up right away. Unplug it again.
  12. Close the motor compartment and put the vacuum back on the wall (if taken off). Connect the low voltage wire back if removed.
  13. Plug it in. Test it again.
  14. If you have any problems or questions don't hesitate to call our customer service toll-free at 1-800-997-2278 Mon-Thurs PST.